How to open a dwg file in siemens 2d st10

HOW TO OPEN A DWG FILE IN SIEMENS 2D ST10 HOW TO

These can always be extracted in the drawing using the Retrieve Dimension command. It is a good practice to add PMI dimensions at the assembly level. Long chains of components take longer to solve and are more prone to relationship errors, unless you are modeling a kinematic link chain of components like a robotic arm. The zone_try_it assembly in the training folder is a good example where the compressor, cooling unit and the fuel tank are all connected directly to the frame structure.ДЄlternatively use the base coordinate system to locate components in an assembly whenever possible. Joining all components to a common component or reference geometry is a good practice since it reduces complexity.ДЇor example, insert the typical base plate, main frame or the chassis as the first component and try to add relationships of subsequent components all to this single part when possible. The axes of the base coordinate systems in Solid Edge can also act as virtual reference planes when the mouse is hovered in the space between them, but the underlying idea of symmetry remains the same. In short, keep your eyes open and be opportunistic. In some cases though, as seen in the image below, it is a good practice to not only model parts symmetric about the base reference planes but also relate the base plate to the base reference planes of the assembly. This however holds good when the entire assembly is symmetric on one side of a plane. This will necessitate creating additional reference planes for mirroring it. If you are dropping the first part into the assembly which is known to be a symmetric one, make sure you donвЂ™t end up relating its reference planes with the base reference planes in the assembly. Join symmetrical assemblies to a mid-plane or axes. Use the Flashfit relationship when applicable, which not only reduces the number of steps required but also automatically applies the optimum or least number of relationships required to fully define or constrain the part.

HOW TO OPEN A DWG FILE IN SIEMENS 2D ST10 HOW TO

Though Solid Edge allows redundant relationships and the animation in the first tip in this set shows how to further explore each relation in detail, suppress or delete any redundant relationships. See tip #1 in this set of tips which shows how to easily lookup the status of a component in the Pathfinder. So it goes without saying to use only as many relationships as are needed to control component position and movement. Relationships consume memory and take longer to solve. Watch and listen to a video created recently which illustrates this: Solid Edge provides a beautifully thought out and executed functionality to achieve this by allowing to reorient the part in the preview area itself. Reorient components into the approximately close orientation before dropping them into the assembly. This gives the solver engine a better chance of snapping components into the right location.ДЄgreed this is not always possible since there could be times when a part is placed in different orientations. Model a part in the same orientation as its layout in the assembly. Without a doubt creating assembly relationships form the bulk of activities when assembling components, so 5 of 12 best assembly practices shared below revolve around managing them. Solid Edge assembly productivity tips that will fetch you success overnight.Solid Edge LARGE assembly best practices, nor.I am no sheetmetal expert and drawing best practices would be a never-ending saga since it is difficult to demarcate what could possibly constitute the best 6 or top 10 drafting best practices in Solid Edge.ДЇurther, assembly best practices could be easily confused with вЂlarge assemblyвЂ™ management tips but skimming through the articles on solid and surface modeling best practices, you can easily catch the drift. Surfacing: Techniques from the Trenches were followed by a flurry of requests for synchronous best practices, assembly, sheetmetal and draft best practices. My best practices articles The 10 Golden Rules of Solid Modeling and Whereas part modeling mistakes are a great deal easier to rectify when problems are found in downstream drafting, simulation or rendering, the same cannot be said about the assembling process which necessarily calls for meticulous planning. Best practices come from practical experience and experience is simply the name we give to our mistakes.ДЄlso, we spend very less time assembling in Solid Edge compared to part modeling and drafting. The greatest challenge faced when collating a bunch of best practices is to differentiate them from tips and tricks.

How to open a dwg file in siemens 2d st10